18.5mm 40kHz Tinned Copper Wire Waterproof Ultrasonic Wire Sensor for Agv Robot

• Customization: Available
• Type: Ultrasonic Wire Sensor
• Output Signal Type: Ultrasonic
• Model NO.: KT40-1431B
• Production Process: Nylon
• Sensitivity: Medium
• Probe Type: Straight Probe
• Measuring Medium: Gas
• Detection mode: Ultrasonic Distance Sensor
• IP Rating: IP67
• Certification: CE/FCC/RoHS
• Customized: Customized
• Function: Tx-Rx Dual-Use
• Center Frequency: 40kHz
• Ringing Time: Less Than or Equal to 1.8ms
• Max. Input Voltage: 140vp-P
• Operating Temp: -40 to +85 Celsius
• Storage Temp: -40 to +85 Celsius
• Color: Black/White
• Hole Dimension: 19mm
• Terminal: Xh2.54 * 2pin
• Transport Package: Carton
• Specification: customized
• Trademark: Kangtong
• Origin: China, Shenzhen
• HS Code: 9031809090
• Production Capacity: 4000PCS/Week
• Package Size: 40.00cm * 30.00cm * 30.00cm
• Package Gross Weight: 5.000kg

Product Description

1.Electrical performance specifications & physical characteristics               

No.	Items	Standard and test condition
1	Function	Transmitter-Receiver
2	Center frequency(KHz)	40.0±1.0(Piezoelectric impedance analyzer)
3	Sensitivity(us)	≥200(normal temp test 0.8mΦ75mmPVC pipe)
4	Residual oscillation(ms)	<=1.52(Normal temp test including transmitting fundamental wave)
5	Capacitance(pF)(25ºC)	1800±15%
6	Beam direction angle(deg)(º)	Vertical    70±15
7	Ranging	>=0.8m(normal temp test Φ75mmPVC pipe)
8	Max Input Voltage(Vp-p)	140 (pulse width 0.5ms, interval 10ms)
9	Operating Temperature (ºC)	-30~+80
10	Storage Temperature (ºC)	-40~+85
11	Terminal	XH2.54*2P Connector
12	Length(mm)	2500±30mm customized
13	Weight(g)	45
14	Color	Customized
15	Outer shell material	Plastic

 

2.Product picture




3. Environmental test

No.	Test items	Test condition	Standard
1	High temp storage test	144 hours at + 85 ºC	After the test and place in + 25 ºC (room temp) for 24 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
2	Low temp storage test	144 hours at - 40 ºC
3	High temp and high humidity storage test	144 hours at + 65 ºC and 85 ± 5% RH
4	Thermal shock test	Parallel 3.9k Ω resistor at both ends of the probe, keep the temp at - 40 ± 5 ºC for 0.5h, and increase the temp to 85 ± 5 ºC within 5 minutes and keep for 0.5h.100 cycles.	After the test and place in + 25 ºC (room temp) for 24 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
5	Vibration test	Products bear the vibration with frequency 10-55hz, amplitude 1.5mm,and sweep rate 1oct / min, from X, Y and Z directions for each 2 hours respectively	After the test and place in + 25 ºC (room temp) for 4 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
6	Monomer drop test	15 free fall tests carried out from 100 ± 10cm height to 50mm thick wooden floor	After the test and place in + 25 ºC (room temp) for 4 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
7	Strength test of outlet	Apply 9.8N pulling force between shell and wire for 30 seconds	The wire is not loose or falling off, the product function is normal, and the wire is not damaged
8	Protection level	Place the probe in 15cm deep water and soak for 24 hours	Take out the probe from the water and install it on the test board to measure the distance. The probe works normally without long sound.
9	High and low temp characteristic test	Keep the temp at -40ºC for 2h,increase to 25ºC and keep for 2h,increase to 85ºC and keep for 2h.	After the test and place in + 25 ºC (room temp) for 2 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
10	High and low temp working test	Under high temp 85 ºC, low temp - 40 ºC, working voltage 140 Vp-p, pulse number 20, continuous working 48 hours	Probe works normally (sensitivity and residual vibration are within normal range)

4.Test conditions and instruments

No.	Test item	Test instruments/method	Test condition
1	resonant frequency	Impedance analyzer	ambient temperature 25 ± 5 ºC
2	static capacitance	LCR bridge measuring instrument	ambient temperature 25 ± 5 ºC
3	residual oscillation	KT test equipment	ambient temperature 25 ± 5 ºC
4	sensitivity	KT test equipment	0.8m at room temperature, target Φ 75mm PVC pipe
5	Angle (X & Y axis)	KT test board, as per Fig.1	Under normal room temperature, the probe is 500mm from the ground, 500mm from the object to be detected, and the object to be detected is Φ 75mm PVC pipe, 1000mm high. The test environment: 2 meters in front and 1.5m in the left and right without obstacles
6	Maximum allowable input voltage	KT test board and Oscilloscope	140vp-p, pulse width 0.5ms, interval 10ms
7	Mean time between failures	aging test rack	Test temp 25±5ºC

5.Detection angle test diagram

6.Precautions
1. The product can only be used in the air, not in liquid
2. In order to prevent the sensor from failure, working failure or performance degradation, the anti failure function shall be added to the product design, and the product shall not be used under the following or similar conditions.
(a) strong shock or vibration
(b) prolonged exposure to high temperature and humidity;
(c)In corrosive gas or sea breeze
(d)Exposure to dissolved organic matter
(e)Dusty environment;
(f)Over allowable input voltage
7.Quality assurance
The sensor defects due to the manufacturer during the warranty period of the product can be replaced free of charge.
The following situations are not covered by the warranty.

1. improper use or handling by users.
2. changed or repaired by the users.
3. any other situation that does not belong to the responsibility of the manufacturer, such as natural disasters, accidents, etc.