40kHz Open Type Transceiver Split Waterproof Ultrasonic Sensor

Product Description

 

*** Welcome to KongTong***

We offer all kinds of Electronic Components ( High frequency sensor ,  Wire harness sensor , Ultrasonic sensor ,Module , Parking sensor, Tire pressure monitor,  Etc.) with a wide range, Good quality, Factory prices and Stylish designs according to your need

More quantity, please contact me about best price and postage 

More quantity, please contact for best discount and postage 

(Support bulk orders and Custom service orders )

 1, Product photos:   KT40-098





 

2, Part Description:
1	Independent RX and TX
2	Water proof
3	extension wire harness (Dia 3.0mm x 200mmL)
4	2P connect with capsule. Left for positive and right for negative with copper Pin
3, Electronic specification & physical character
	Description	Standard or testing result		Item	Description	Standard or testing result
1	Part Number	KT40-098		8	Detective angle	120°±15°
2	Match sensor number	KT40-T/R1011		9	Intermittent space (ms)	50
3	Center frequency(KHz)	40±1KHz		10	Protocal	TTL
4	Operation voltage	5V		11	Connect	JST: B04B-XNISK-A-1  or custermization
5	Operation current	≤20mA		12	Sensor colour	Natural aluminum or customization
6	Detective distance (Max.)	2m		13	Stock temperature	-20-70ºC
7	Blind detective distance	2cm±1cm		14	Operation temperature	-10ºC~60ºC
4,Dimension and detective diagram

 

 

5. Environmental test
No.	Test items	Test condition			Standard
1	High temp storage test	144 hours at + 85 ºC			After the test and place in + 25 ºC (room temp) for 24 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
2	Low temp storage test	144 hours at - 40 ºC
3	High temp and high humidity storage test	144 hours at + 65 ºC and 85 ± 5% RH
4	Thermal shock test	Parallel 3.9k Ω resistor at both ends of the probe, keep the temp at - 40 ± 5 ºC for 0.5h, and increase the temp to 85 ± 5 ºC within 5 minutes and keep for 0.5h.100 cycles.			After the test and place in + 25 ºC (room temp) for 24 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
5	Vibration test	Products bear the vibration with frequency 10-55hz, amplitude 1.5mm,and sweep rate 1oct / min, from X, Y and Z directions for each 2 hours respectively			After the test and place in + 25 ºC (room temp) for 4 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
6	Monomer drop test	15 free fall tests carried out from 100 ± 10cm height to 50mm thick wooden floor			After the test and place in + 25 ºC (room temp) for 4 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
7	Strength test of outlet	Apply 9.8N pulling force between shell and wire for 30 seconds			The wire is not loose or falling off, the product function is normal, and the wire is not damaged
8	Protection level	Place the probe in 15cm deep water and soak for 24 hours			Take out the capasual from the water and install it on the test board to measure the distance. The probe works normally without long sound.
9	High and low temp characteristic test	Keep the temp at -40ºC for 2h,increase to 25ºC and keep for 2h,increase to 85ºC and keep for 2h.			After the test and place in + 25 ºC (room temp) for 2 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
10	High and low temp working test	Under high temp 85 ºC, low temp - 40 ºC, working voltage 140 Vp-p, pulse number 20, continuous working 48 hours			Probe works normally (sensitivity and residual vibration are within normal range)
6.Test conditions and instruments
No.	Test item	Test instruments/method			Test condition
1	resonant frequency	Impedance analyzer			ambient temperature 25 ± 5 ºC
2	static capacitance	LCR bridge measuring instrument			ambient temperature 25 ± 5 ºC
3	residual oscillation	KT test equipment			ambient temperature 25 ± 5 ºC
4	sensitivity	KT test equipment			0.8m at room temperature, target Φ 75mm PVC pipe
5	Angle (X & Y axis)	KT test board, as per Fig.1			Under normal room temperature, the probe is 500mm from the ground, 500mm from the object to be detected, and the object to be detected is Φ 75mm PVC pipe, 1000mm high. The test environment: 2 meters in front and 1.5m in the left and right without obstacles
6	Maximum allowable input voltage	KT test board and Oscilloscope			140vp-p, pulse width 0.5ms,
					intermittent: 10ms
7	Mean time between failures	aging test rack			Test temp 25±5ºC
7.Precautions
1. Please confirm with us which industry will be used before purchasing for selection. 2. In order to prevent the sensor from failure, working failure or performance degradation, the anti failure    function shall be added to the product design, and the product shall not be used under the following or    similar conditions.    (a) strong shock or vibration    (b) prolonged exposure to high temperature and humidity;    (c)In corrosive gas or sea breeze    (d)Exposure to dissolved organic matter    (e)Dusty environment;    (f)Over allowable input voltage

8.Competitive advantage:

1, High quality control based on IATF16949 system;

2, 100% functional testing before shipping;

3, Strong anti-interference capacity;

4, Entire copper core for wireharness;

5, Water proof with IP67 grade or over;

6, ERP system for material controlling

7, Capability and experienced work with Toyota, Honda car maker;

8, Sensor lab for best quality;

9, Automotive sensor capsule production line; 

10,  Capability for completed product capability included ID, MD, hardware and software for TTL, LIN or Can.

 

Company Profile

 

FAQ

 

FAQ

1.When can we get the reply? 
Any inquiries will be replied within 24 hours. 
Our Kongtong sales team will try our best to support you. 

2.What about minimum order quantity?
We have no limit for MOQ,so you can even buy only 1 piece.
Welcome to buy sample to test first. 

3.Do you have different Ultrasonic Sensor series ?
A: Yes,We have ,you can check my shop or send Email to me 

4.Can customize,modify and develop products according to the design drawing?Yes,wprovide OEM service and can customize products according to the drawing.

5.How will you control product quality?
We strictly control every detail of production, and every product is inspected by our QC team before delivery. Moreover,our production is abided by IATF16949, CE .

6.What about delivery time?
Sample, We will send to you within 3 days after payment received. Production for big quantity needs 3 to 10days. Andit also depends on product and quantity.
If want to know the exact time. Email us the quantity,
We will check the time for you.

7.What about terms of payment?
Payment terms: T/T,  west Union , Paypal and L/C etc.

8.How do I know that you have sent the products out?
Once the products are sent out, a tracking number will be provided so that you can check where your goods at all times

9.How you will send the goods to us?
We will send the goods to you by DHL,FEDEX,UPS, EMS,AIR ,Sea Transportation etc. Or Shipping Methods as you request